1A
DTC P1675: CAN Communication (Transmission Error)
Wiring Diagram
[A]: ECM connector (viewed from harness side) 1. ECM
[B]: TCM connector (viewed from harness side) 2. TCM
DTC Detecting Condition and Trouble Area
DTC detecting condition Trouble area
Transmission error of communication data for ECM is detected for longer than specified time continuously.
(1 driving detection logic)
ECM
TCM
CAN communication line circuit
DTC Confirmation Procedure
1) Connect scan tool to DLC with ignition switch OFF.
2) Turn ON ignition switch and clear DTC by using scan tool.
3) Start engine and run it for 1 min. or more.
4) Check DTC and pending DTC.
DTC Troubleshooting
Step Action YES NO
1
Was “Engine and Emission Control System Check” performed?
Go to Step 2.
2
DTC check
1) Connect scan tool to DLC with ignition switch turned OFF.
2) Check ECM and TCM for DTC.
Is there any DTC(s) (other than DTC P1674, P1675, P1676 in ECM and DTC P1774, P1775, P1777 in TCM)?
Go to applicable DTC diag. flow.
Go to Step 3.
3
CAN communication error check for ECM
1) Check ECM for DTC.
Is there DTC P1674?
Go to Step 4.
4
CAN communication error check for TCM
1) Check TCM for DTC.
Are there DTC P1774 in TCM?
Go to Step 5.
5
ECM and TCM connectors check
1) Check for proper connection at each ECM and TCM connector terminals with ignition switch turned OFF.
2) If connections are OK, recheck ECM for DTC with engine running.
Is there DTC P1675?
Go to Step 6.
Intermittent trouble. Check for intermittent referring to Intermittent and Poor Connection Inspection .
6
ECM power and ground circuit check
Are they in good condition?
Go to Step 7.
Repair ECM power and/or ground circuits.
7
DTC check in ECM
1) Check ECM for DTC.
Are there DTC P1676?
Go to Step 8.
Go to Step 9.
8
DTC check in TCM
1) Check TCM for DTC.
Are there DTC P1777 in TCM?
Go to Step 9.
Substitute a known-good ECM and recheck.
9
CAN communication line circuit continuity check
1) Disconnect connectors from ECM and TCM with ignition switch turned OFF.
2) Measure resistance at the following connector terminals.
Between “E118-8” terminal of ECM connector and “E121-17” terminal of TCM connector
Between “E118-7” terminal of ECM connector and “E121-7” terminal of TCM connector
Is each resistance below 1 Ω?
Go to Step 10.
Repair open or high resistance of CAN communication line circuit referring to Precaution for CAN Communication System .
10
CAN communication line circuit insulation check
1) Measure resistance at the following connector terminals.
Between “E118-8” and “E118-7” terminals of ECM connector
Is each resistance infinity?
Go to Step 11.
Repair insulation of CAN communication line circuit referring to Precaution for CAN Communication System .
11
CAN communication line circuit ground short check
1) Measure resistance at the following connector terminals.
Between “E118-8” terminal of ECM connector and vehicle body ground
Between “E118-7” terminal of ECM connector and vehicle body ground
Is each resistance infinity?
Go to Step 12.
Repair shorted to ground of CAN communication line circuit referring to Precaution for CAN Communication System .
12
Check for short circuit of CAN communication line to power circuit
1) Measure voltage at the following connector terminals with ignition switch turned ON.
Between “E118-8” terminal of ECM connector and vehicle body ground
Between “E118-7” terminal of ECM connector and vehicle body ground
Is each voltage 0 – 1 V?
Substitute a known-good ECM and recheck.
Repair shorted to power supply of CAN communication line circuit referring to Precaution for CAN Communication System .
NOTE:
Upon completion of inspection and repair work, perform “DTC Confirmation Procedure” and confirm that the trouble has been corrected.